LCN 4010 Series

Specifications

• Standard 4010 series closer is shipped with regular arm, standard plastic cover, and self reaming and tapping screws.

• Sized cylinders for interior doors to 5’0” and exterior doors to 4’0”.

• Non-sized cylinder (4011) adjustable for interior doors to 4’6” and exterior doors to 3’6”.

• Closer mounts hinge side, specify right or left swinging door.

• Corner brackets available – see Options tab for optional parts.

• 4011 cylinder meets ADA requirements.

• Standard or optional custom powder coat finish.

• Optional plated finish on metal cover, arm and fasteners.

• Optional SRI primer for installations in corrosive conditions is available with powder coat only.

• The 4010 Series is UL and cUL listed with regular or fusible link arms for self-closing doors.

• Tested and certified under ANSI Standard A156.4, grade one.

Mounting Details

HINGE (PULL) SIDE: Maximum opening can be templated for 100°:
A = 5-15/16” (151 mm); B = 11-15/16” (303 mm). Maximum opening to 140°:
A = 4-3/16” (106 mm); B = 10-3/16” (259 mm). Hold-open points up to maximum opening with hold-open arm. Arm Clearance above door. Regular arm requires C = 1-1/16” (27 mm). Hold-open arm requires
C = 1-3/8” (35 mm). Fusible link arm requires C = 1-5/8” (41 mm).

• Butt Hinges should not exceed 5” (127 mm) in width.
• Auxiliary Stop is recommended at hold-open point or where a door cannot swing 140°.
• Reveal should not exceed 3/4” (19 mm). Fusible link arm should not exceed 1/8” (3 mm).
• Top Rail less than 3-3/4” (95 mm) requires PLATE, 4010-18.
• Plate requires 2” (51 mm) minimum.
• Clearance of 2-1/4” (57 mm) behind door required for 90° installation.
• Delayed Action Add suffix “DEL” to selected cylinder (eg. 4014 DEL).
• Not available with 4016 cylinder.
• Delays closing from maximum opening to approximately 70°.
• Delay time adjustable up to approximately one minute.
• Bull Nose Trim requires SOFFIT SHOE, 4010-65.
• Corner Bracket for a door where top jamb or parallel arm mounting cannot be used. Consult Penner on all corner bracket mounts.

LCN Finishes

STANDARD POWDER COATED FINISH: LCN door closers feature the finest, state-of-the-art metal finishing process available. LCN powder coating provides superior protection against the effects of weathering and is an environmentally friendly process. The high quality, chip resistant finish is far superior to any previously offered. Corrosion resistance surpasses 100 hours salt spray testing (four times the industry standard). Non-metallic components also provide the same high resistance to the effects of the elements. All LCN products must be shipped with a finish.

OPTIONAL CUSTOM POWDER COATED FINISHES: LCN offers optional custom powder coat colors to compliment special installations. This provides a custom appearance and all the corrosion resistance of standard powder coated finishes at a nominal additional cost. See Downloads tab for available custom colors.

OPTIONAL PLATED FINISHES: Visible components such as covers, arms, fasteners, and finish plates are plated to match the selected finish. Surface mounted tracks are powder coated to complement the plated finish. Hidden assemblies such as cylinders, tracks, and mounting plates are supplied with a powder coated finish.

SPECIAL RUST INHIBITING (SRI) PROCESS: For installations where a higher level of protection against weathering, or the effects of a potentially corrosive atmosphere is required, LCN offers a special rust inhibiting (SRI) process. Ferrous metal components receive an SRI pretreatment and a powder finish coat in your choice of either an LCN standard color or optional extra charge custom colors. Closers treated with the SRI process exceed the 100 hour protection level available with standard LCN powder coated finishes.